![](/i/fill.gif) |
![](/i/fill.gif) |
|
![](/i/fill.gif) |
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
Alain wrote:
>> pretrace_start 0.32
> Changing the pretrace_start usualy have little to no effect. Keep the
> default of 0.08.
> Changing by some small value may, in some cases, get rid of some
> artefacts near corners.
I had some vague notion that it helped with sample distribution, but it
was likely my imagination.
>> pretrace_end 0.02
> Default value.
> Try reducint this to 0.01, 0.005 or 0.0025
>> count 400
> Maybe a larger value here? Try 600 or 800.
>> nearest_count 5
> That's the default value.
> You can go up to 20. Low effect on render time, can greatly improve end
> result.
Gotcha. I was shooting for more defined shadows than I got, so I didn't
really want to average them out too much.
>> error_bound 1
>> recursion_limit 3
> Default value.
>> low_error_factor 0.5
> Meybe try a somewhat smaller value. Will take more time on the final
> pretrace step.
>> gray_threshold 0
> Default value.
>> minimum_reuse 0.015
> Default value.
> You may need a value larger OR smaler. Don't go over 0.02. Don't go to
> small, as smaller values will increase the render time.
Gotcha.
>> brightness 1
> Default value.
>> adc_bailout 0.01/0.4
> That's 0.025, probably to large. Try adc_bailout 0.01/3 or 0.01/4.
Thanks, I'll bet this isn't helping. It didn't seem right, but I didn't
really know where to go with it.
>> normal off
> Default value.
>> media off
> Default value.
>>
> Every time you use a default value, you can skip that option.
>
Thanks for the advice, I appreciate it. I usually put all the options
in there deliberately, even though its often redundant. My memory of
the defaults is fuzzy, so I like to be sure I know exactly the value I'm
using. I also like to see all the values, for me it makes it easier to
tweak them around. Lastly, I think some part of my personality
distrusts default values =)
Post a reply to this message
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
Blue Herring nous illumina en ce 2008-05-21 13:36 -->
> Alain wrote:
>>> pretrace_start 0.32
>> Changing the pretrace_start usualy have little to no effect. Keep the
>> default of 0.08.
>> Changing by some small value may, in some cases, get rid of some
>> artefacts near corners.
>
> I had some vague notion that it helped with sample distribution, but it
> was likely my imagination.
>
>>> pretrace_end 0.02
>> Default value.
>> Try reducint this to 0.01, 0.005 or 0.0025
>>> count 400
>> Maybe a larger value here? Try 600 or 800.
>>> nearest_count 5
>> That's the default value.
>> You can go up to 20. Low effect on render time, can greatly improve
>> end result.
>
> Gotcha. I was shooting for more defined shadows than I got, so I didn't
> really want to average them out too much.
>
>>> error_bound 1
>>> recursion_limit 3
>> Default value.
>>> low_error_factor 0.5
>> Meybe try a somewhat smaller value. Will take more time on the final
>> pretrace step.
>>> gray_threshold 0
>> Default value.
>>> minimum_reuse 0.015
>> Default value.
>> You may need a value larger OR smaler. Don't go over 0.02. Don't go to
>> small, as smaller values will increase the render time.
>
> Gotcha.
>
>>> brightness 1
>> Default value.
>>> adc_bailout 0.01/0.4
>> That's 0.025, probably to large. Try adc_bailout 0.01/3 or 0.01/4.
>
> Thanks, I'll bet this isn't helping. It didn't seem right, but I didn't
> really know where to go with it.
>
>>> normal off
>> Default value.
>>> media off
>> Default value.
>>>
>> Every time you use a default value, you can skip that option.
>>
>
> Thanks for the advice, I appreciate it. I usually put all the options
> in there deliberately, even though its often redundant. My memory of
> the defaults is fuzzy, so I like to be sure I know exactly the value I'm
> using. I also like to see all the values, for me it makes it easier to
> tweak them around. Lastly, I think some part of my personality
> distrusts default values =)
>
>
>
When I say that you can skip a parameter with default value, I never sayd that
you /must/ keep those set at default value. If keeping those help you, then keep
them.
--
Alain
-------------------------------------------------
Advertisements contain the only truths to be relied on in a newspaper.
Thomas Jefferson
Post a reply to this message
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
Alain wrote:
> When I say that you can skip a parameter with default value, I never
> sayd that you /must/ keep those set at default value. If keeping those
> help you, then keep them.
I understand, I think my reply was just a little unclear.
--
-The Mildly Infamous Blue Herring
Post a reply to this message
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |