![](/i/fill.gif) |
![](/i/fill.gif) |
|
![](/i/fill.gif) |
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
Hi,
The latch from the earlier image I had posted. Is there a way to texture
this better?
Regards,
Rishi
Post a reply to this message
Attachments:
Download 'Latch.jpg' (46 KB)
Preview of image 'Latch.jpg'
![Latch.jpg](/povray.binaries.images/attachment/%3C43c0126e%40news.povray.org%3E/Latch.jpg?ttop=443866&toff=4750&preview=1)
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
Rishi wrote:
> Hi,
>
> The latch from the earlier image I had posted. Is there a way to texture
> this better?
>
> Regards,
>
> Rishi
>
>
>
looks quite confincing to me, but as you ask ;-) :
- forged iron normaly have same small ditches, so it could be worth to
add some bumps (also it's normaly darker especially if it allready got
patina)
- the wood texture is to repetative, you may simple move it a little
bit from plank to plank and add some black-hole warps to fake parts
where the branches were
... dave
Post a reply to this message
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
"Rishi" <raj### [at] gmail com> wrote in message
news:43c0126e@news.povray.org...
> Hi,
>
> The latch from the earlier image I had posted. Is there a way to texture
> this better?
>
> Regards,
>
> Rishi
The weathered iron looks good.
The surfaces are way too flat (e.g. straight shadows at plank joints).
The other issue is nonsensical placement.
The worn part of the iron shaft when translated to the right (under the
anchor) would not align the hasp and staple.
And I'm not sure it can travel far enough to make it without a collision of
the anchor and hasp. Perhaps move the staple to the left?
I'd also like to see the right edge of the door. And the third anchor.
The screws look too small for the load they support, and the 4 screws on the
hasp look superfluous.
DLM
Post a reply to this message
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
"Rishi" <raj### [at] gmail com> wrote...
> Hi,
>
> The latch from the earlier image I had posted. Is there a way to texture
> this better?
Be sure to get rid of ALL "ambient" lighting in the textures. Use radiosity
intead for much greater realism.
-Nathan
Post a reply to this message
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
"Nathan Kopp" <pov### [at] nkopp mailshell com> wrote:
> "Rishi" <raj### [at] gmail com> wrote...
> > Hi,
> >
> > The latch from the earlier image I had posted. Is there a way to texture
> > this better?
>
Rishy, yes better. I was used "rust_iron" texture, the result :
Hasan
Regards.
Post a reply to this message
Attachments:
Download 'kilit2.jpg' (129 KB)
Preview of image 'kilit2.jpg'
![kilit2.jpg](/povray.binaries.images/attachment/%3Cweb.43c2ca2069c11807703a268a0%40news.povray.org%3E/kilit2.jpg?ttop=443866&toff=4750&preview=1)
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |