![](/i/fill.gif) |
![](/i/fill.gif) |
|
![](/i/fill.gif) |
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
Francois Labreque <fla### [at] videotron ca> wrote:
>
>Very good. I can almost hear the hum of the amplifier...
Thank you
>I think the metallic pin looks more like grey plastic. Try modifying
>the highlight and putting radial microscopic scratches resulting from
>the manufacturing process. As thers have mentioned, the kink in the
>wire is a bit too severe.
Ok...will give it a try
Oldstench................
Post a reply to this message
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
ste### [at] zeropps uklinux net (Steve) wrote:
>I like the cable, how did you do it?
Thank you...all modelling was done in Rhino, imported into Moray and
textured there.. The wire is a spline with a pipe extruded around it.
>The metal part of the plug looks very old and tarnished, so on that
>table you need coffe stains, some ash strewen about, an old casset
>tape in bits etc.
I like the idea about a tape...shall try that next
>The reason I never get anything done is because I keep getting new
>ideas, what an inspirational lot you all are:-)
Oldstench................
Post a reply to this message
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
"Bill DeWitt" <bde### [at] cfl rr com> wrote:
> Hmm... the radius of the bend in the wire makes it look like either the
>wire is -much- softer than it should be, or that the plug is -much- larger
>than it should be.
I am sensing a pattern....
> Otherwise the modeling is great. Comparing it to what I have here, it is
>almost perfect in dimensions and textures.
>
Thanks
Oldstench................
Post a reply to this message
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
"Oldstench" <sor### [at] butno com> wrote in message
news:4sg6itgu6p26dlbov37i842dimqnpujh4b@4ax.com...
> Any ideas what else should be in the scene?....comments welcome too.
Looks nice! My only complaint is that the metal looks too "foggy". If you
make it a little more reflective, that should do the trick!
-Ian
Post a reply to this message
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |
| ![](/i/fill.gif) |
|
![](/i/fill.gif) |
|
![](/i/fill.gif) |
| ![](/i/fill.gif) |