|
|
|
|
|
|
| |
| |
|
|
|
|
| |
| |
|
|
Afternoon, all...
I am calling "pvengine" with required command line options including
/EXIT. However, after calling/launching PovRay 3.1 for Windows, rendering
the image and writing a BMP file, I cannot seem to return to the calling
program(Perl). My program requires that I call PovRay a number
of times. Unfortunately, program control is lost after the first call.
Can anyone help?
Regards...Bob
Post a reply to this message
|
|
| |
| |
|
|
|
|
| |
| |
|
|
On Mon, 13 Oct 2003 15:11:43 -0400, "Bob Rasmussen" <bob### [at] comcastnet>
wrote:
> PovRay 3.1 for Windows
Can't you try it with POV-Ray 3.5 for Windows ? Any support will be easier
then...
ABX
Post a reply to this message
|
|
| |
| |
|
|
|
|
| |
| |
|
|
"ABX" <abx### [at] abxartpl> wrote in message
news:fculovgd1u1j6l5b4foi60rgckfdcodope@4ax.com...
> On Mon, 13 Oct 2003 15:11:43 -0400, "Bob Rasmussen" <bob### [at] comcastnet>
> wrote:
> > PovRay 3.1 for Windows
>
> Can't you try it with POV-Ray 3.5 for Windows ? Any support will be easier
> then...
>
> ABX
I was hoping there was a simple command string option that would permit
PovRay to run in the background and return me to the program. Do you
know if such an option is available in 3.5? In the Unix version (PovRay 1.0)
I was
returned to my Perl program, but, in the Windows version the image is
rendered and a BMP file is output, but, I'm not returned to the program.
There is a caution on the PovRay web site about switching to 3.5 over
3.1. I wasn't sure that files created in 3.1 were compatible with 3.5.
The string below is my command string (Perl5)
system "c:\\Povray31\\bin\\pvengine.exe -D -P -GA +X +A /EXIT
+Lc:\\Povray31\\Include +Ic:\\Perl5\\$prefix.pov +Oc:\\Perl5\\$prefix.bmp
+W500 +H900 +FS"
PovRay runs, creates the BMP file, but, does not execute the next Perl5
command. Any thoughts?
Thanks for your interest...Bob
Post a reply to this message
|
|
| |
| |
|
|
|
|
| |
| |
|
|
"Bob Rasmussen" <bob### [at] comcastnet> wrote in
news:3f8af81c$1@news.povray.org:
> Can anyone help?
>
> Regards...Bob
>
>
my $povpath='C:\Program Files\POV-Ray for Windows v3.5\bin\pvengine.exe';
my $povflag='/nr /exit';
my $pov_return;
$pov_return=system("\"$povpath\" task.ini $povflag");
You may want to try POVCyg and eliminate the GUI altogether.
http://www-public.tu-bs.de:8080/~y0013390/povcyg/
my $povpath='C:\Program Files\POVCyg\povray.exe';
my $povflag='-GR -GS +V';
my $pov_return;
$pov_return=system("\"$povpath\" task.ini $povflag");
--
Tom
_________________________________
The Internet Movie Project
http://www.imp.org/
Post a reply to this message
|
|
| |
| |
|
|
From: Thorsten Froehlich
Subject: Re: Need to return to calling program
Date: 14 Oct 2003 13:33:42
Message: <3f8c3376@news.povray.org>
|
|
|
| |
| |
|
|
In article <3f8af81c$1@news.povray.org> , "Bob Rasmussen"
<bob### [at] comcastnet> wrote:
> I am calling "pvengine" with required command line options including
> /EXIT. However, after calling/launching PovRay 3.1 for Windows, rendering
> the image and writing a BMP file, I cannot seem to return to the calling
> program(Perl). My program requires that I call PovRay a number
> of times. Unfortunately, program control is lost after the first call.
> Can anyone help?
This is the wrong group for this question. This group is for discussion of
the POV-Ray source code. General questions about using the POV-Ray scene
description language should be asked in either povray.general or
povray.newusers. Questions about a particular platform version of the
POV-Ray application supported by the POV-Team should be asked in the
newsgroup for that particular platform or povray.newusers.
Thorsten
____________________________________________________
Thorsten Froehlich
e-mail: mac### [at] povrayorg
I am a member of the POV-Ray Team.
Visit POV-Ray on the web: http://mac.povray.org
Post a reply to this message
|
|
| |
| |
|
|
|
|
| |